Nondestructive Evaluation (NDE) Methods and Capabilities Handbook - Volume II Appendices - Appendix E Volume 2

No abstract availabl

Nondestructive Evaluation (NDE) Methods and Capabilities Handbook - Volume II Appendices - Appendix E Volume 1

No abstract availabl

Nondestructive Evaluation (NDE) Methods and Capabilities Handbook - Volume II Appendices - Appendix A - Appendix D

No abstract availabl

Quadruple Simulations of Thermographic Inspections of Impacted Composites

Thermography has been shown to be a viable technique for inspection of composites. Impact damage in composites typically contains multiple overlapping delaminations at different depths. Understanding the limitations of the thermographic inspection is enhanced by performing simulations of the technique. Most simulations of composite thermographic inspections have focused on simulations of a single delamination at a fixed depth. The quadrupole method has been shown as a viable technique for rapid three-dimensional thermographic simulations of a delamination. This method is expanded to enable rapid simulation of multiple overlapping delaminations at different depths. Quadrupole simulations are compared to finite element simulations of multiple delaminations at different depths. The simulations are also compared to the thermographic measurements on impacted composites where shape and depth of the delaminations are known from x-ray computed tomography data

Results of On-Orbit Testing of an Extra-Vehicular Infrared Camera Inspection System

This paper will discuss an infrared camera inspection system that has been developed to allow astronauts to demonstrate the ability to inspect reinforced carbon-carbon (RCC) components on the space shuttle as part of extra-vehicular activities (EVA) while in orbit. Presented will be the performance of the EVA camera system coupled with solar heating for inspection of damaged RCC specimens and NDE standards. The data presented was acquired during space shuttle flights STS-121 and STS-115 as well during a staged EVA from the ISS. The EVA camera system was able to detect flatbottom holes as small as 2.54cm in diameter with 25% material loss. Results obtained are shown to be comparable to ground-based thermal inspections performed in the laboratory using the same camera and simulated solar heating. Data on both the time history of the specimen temperature and the ability of the inspection system to image defects due to impact will likewise be presented

Improved Flaw Detection and Characterization with Difference Thermography

Flaw detection and characterization with thermographic techniques in graphite polymer composites is often limited by localized variations in the thermographic response. Variations in properties such as acceptable porosity, variations in fiber volume content and surface polymer thickness result in variations in the thermal response that in general cause significant variations in the initial thermal response. These variations result in a noise floor that increases the difficulty of detecting and characterizing deeper flaws. The paper investigates comparing thermographic responses taken before and after a change in state in a composite to improve the detection of subsurface flaws. A method is presented for registration of the responses before finding the difference. A significant improvement in the detectability is achieved by comparing the differences in response. Examples of changes in state due to application of a load and impact are presented

Improved Sizing of Impact Damage in Composites Based on Thermographic Response

Impact damage in thin carbon fiber reinforced polymer composites often results in a relatively small region of damage at the front surface, with increasing damage near the back surface. Conventional methods for reducing the pulsed thermographic responses of the composite tend to underestimate the size of the back surface damage, since the smaller near surface damage gives the largest thermographic indication. A method is presented for reducing the thermographic data to produce an estimated size for the impact damage that is much closer to the size of the damage estimated from other NDE techniques such as microfocus x-ray computed tomography and pulse echo ultrasonics. Examples of the application of the technique to experimental data acquired on specimens with impact damage are presented. The method is also applied to the results of thermographic simulations to investigate the limitations of the technique

Computational Reduction of Specimen Noise to Enable Improved Thermography Characterization of Flaws in Graphite Polymer Composites

Flaw detection and characterization with thermographic techniques in graphite polymer composites are often limited by localized variations in the thermographic response. Variations in properties such as acceptable porosity, fiber volume content and surface polymer thickness result in variations in the thermal response that in general cause significant variations in the initial thermal response. These result in a "noise" floor that increases the difficulty of detecting and characterizing deeper flaws. A method is presented for computationally removing a significant amount of the "noise" from near surface porosity by diffusing the early time response, then subtracting it from subsequent responses. Simulations of the thermal response of a composite are utilized in defining the limitations of the technique. This method for reducing the data is shown to give considerable improvement characterizing both the size and depth of damage. Examples are shown for data acquired on specimens with fabricated delaminations and impact damage